Fasteners · 5 min read

M10, M8, M6 and M5 rivet nuts — what hole should you drill?

Correctly selecting the drilled hole diameter is important for the durability and safety of a threaded connection. Even a small inaccuracy can cause the component to s...

Correctly selecting the drilled hole diameter is important for the durability and safety of a threaded connection. Even a small inaccuracy can cause the component to spin in the material, preventing stable bolt installation. In maintenance engineering, seating precision determines trouble-free component operation, so the process requires a rigorous approach. In this article, we explain which hole is suitable for M8 rivet nuts, M6, M10 and M5.

Contents

  • Hole preparation — general principles
  • M10, M8, M6 and M5 rivet nuts — what hole should you drill?
    • M5 rivet nuts — what hole should you prepare?
    • What hole is recommended for an M6 rivet nut?
    • What hole should you drill for M8 rivet nuts?
    • What is the best hole for an M10 rivet nut?
  • What equipment is useful for installing rivet nuts?
  • Start by preparing precision equipment from the Neron store

Hole preparation — general principles

Preparing a seat for a rivet nut requires strict process control to ensure optimal anchoring in the base material. During this process, keep the following in mind.

  • correct tool selection — use only serviceable drills with hardness suited to the material being machined,
  • drilling geometry — the hole must be perpendicular to the sheet surface so the rivet nut flange rests evenly against it,
  • finishing — thoroughly remove burrs and swarf that could hold the flange away from the material.

Care over the cleanliness and precision of the seat edges directly eliminates the risk of subsequent connection loosening during machine operation.

M10, M8, M6 and M5 rivet nuts — what hole should you drill?

Maintaining the correct fit is an important factor guaranteeing proper installation. As a standard rule, the diameter is taken to be 0,1 mm larger than the component's outside dimension. A seat that is too tight can damage the corrosion-protection coating, while one that is too loose will not allow the sleeve to upset correctly. Below we present the most important information on which hole for rivet nuts M5, M6, M8 and M10 will work best.

M5 rivet nuts — what hole should you prepare?

For an M5 rivet nut , the question of which hole to make is affected by its outside diameter of 7 mm. Accordingly, a 7,1 mm diameter drill is used to obtain the proper fit. These dimensions are an optimal solution in structural components with wall thicknesses from 0,5 mm to 3,0 mm.

What hole is recommended for an M6 rivet nut?

Many customers ask our store “what hole should I drill for an M6 rivet nut?” In this case, the best option is 9,1 mm. Thanks to the optimal contact area after upsetting, this size is ideal for securing brackets, cable trays or guards in hollow sections where access from the other side is unavailable.

What hole should you drill for M8 rivet nuts?

A seat with an 11,1 mm diameter is the ideal answer to the question of what hole for M8 rivet nuts to prepare. This size is widely used in heavy machine construction, steel structures and mounting agricultural suspension components. Due to the greater clamping force, seat precision is important here to avoid axial movement under load. Using a drill of HSS-Co hardness ensures the clean cutting edge needed for full stability of such a strong joint.

What is the best hole for an M10 rivet nut?

When securing points subjected to substantial mechanical loads, a particularly important question is what hole for an M10 rivet nut you drill. Correct installation requires a tool with a diameter of 13,1 mm. Remember to use low spindle speeds and coolants to prevent material overheating. At this joint size, every geometric inaccuracy is amplified by the bolt tightening force, so drills with a thinned web are recommended.

The choice of what hole for M8 rivet nuts or M5 you choose requires exceptional dimensional precision. Remember that the above guidelines apply to standard steel and aluminium components. For specialist models, checking dimensions against the manufacturer's current catalogue sheet is always recommended.

What equipment is useful for installing rivet nuts?

Correct fastener installation requires professional equipment that guarantees repeatability and clamping force. The Neron store range includes solutions ideal for intensive industrial use. Before starting, obtain the following.

  • Rivet nut setting tool — confirm supported thread sizes and rivet nut material before purchasing. Help with equipment selection is available through NERON contact page.
  • drills — high-quality HSS DIN 338products, ideal for precision drilling in hard steels,
  • technical chemicals — lubricants and coolants that reduce drilling friction and protect threads against galling.

Fully equipping a workshop with certified tools eliminates the risk of assembly errors and significantly speeds up servicing. Contact our advisers for precise equipment selection.

Start by preparing precision equipment from the Neron store

Whether you choose rivet nuts M5 or M8, the question of which hole you drill is fundamental to a durable connection. Every stage, from drill selection to final upsetting, affects the stability of the machine structure. At Neron, we supply only proven solutions meeting strict technical standards. Explore our range of rivet nuts in the NERON store.

Rivet nuts

Select the right hole and order M5, M6, M8 and M10 rivet nuts from a trusted store

M5 → hole 7,1 mm M6 → hole 9,1 mm M8 → hole 11,1 mm M10 → hole 13,1 mm View rivet nuts in the store
Loading...
Back to top