
Angular contact ball bearing dimensions are written as d × D × B: bore diameter, outside diameter and width. When selecting a substitute, also read the manufacturer an...
Angular contact ball bearing dimensions are written as d × D × B: bore diameter, outside diameter and width. When selecting a substitute, also read the manufacturer and full designation. The number “3200” alone does not determine every detail: SKF 3200 ATN9 measures 10 × 30 × 14 mm, while ZVL 3200 measures 10 × 30 × 14,3 mm. The width difference matters for installation space.
Which bearings do the 3200 and 3300 tables cover?
The following tables cover double-row angular contact ball bearings in dimension series 32 and 33. They do not cover all angular contact bearings. The double-row design can carry radial loads and axial loads in both directions; permissible values must be checked for the specific design.
The tables help identify size but do not confirm interchangeability. Matching d, D and B does not mean the same contact angle, clearance, cage, seal, load rating or permissible speed. Compare these data with the machine documentation and manufacturer's sheet.
What do d, D and B mean? How do you check the size?
- d — bore diameter of the inner ring.
- D — outside diameter of the outer ring.
- B — bearing width along its axis.
The example dimensions 25 × 52 × 20,6 mm mean a 25 mm bore, 52 mm outside diameter and 20,6 mm width. They do not mean three diameters.
- Record the entire designation from the ring or packaging, including letters, symbols and manufacturer name. If machine documentation is available, compare it as well.
- Remove loose dirt from the measuring surfaces. Check that burrs or damage do not distort the reading.
- Measure d, D and B with the instrument held square. For width, measure across the ring faces, not a protruding seal or cage part.
- Compare the result with the nominal dimension of the specific design. Do not automatically round a reading of “about 14 mm” to 14,3 mm or vice versa.
This is a preliminary part-identification procedure. Measuring a worn bearing with callipers does not confirm tolerances, shaft or housing fits, or internal clearance. Such requirements come from the documentation and appropriately precise measurements.
Series 32 angular contact bearings — selected dimensions
Dimensions in millimetres according to the catalogues of the named manufacturers. Each row applies to the specified design, not any product with a similar number. The tables do not declare current availability of these brands in the shop.
Manufacturer | d | D | B |
|---|---|---|---|
ZVL | 10 | 30 | 14,3 |
SKF | 10 | 30 | 14 |
ZVL | 12 | 32 | 15,9 |
ZVL | 15 | 35 | 15,9 |
ZVL | 17 | 40 | 17,5 |
ZVL | 20 | 47 | 20,6 |
ZVL | 25 | 52 | 20,6 |
SKF | 30 | 62 | 23,8 |
SKF | 35 | 72 | 27 |
SKF | 40 | 80 | 30,2 |
Why are there two 3200 rows in the table? They show a real difference between the specified products: 14 and 14,3 mm. This is not a recommendation to substitute one for the other. Do not automatically apply these data to other suffixes or brands.
Series 33 angular contact bearings — selected dimensions
Manufacturer | d | D | B |
|---|---|---|---|
ZVL | 10 | 35 | 19 |
ZVL | 12 | 37 | 19 |
ZVL | 15 | 42 | 19 |
ZVL | 17 | 47 | 22,2 |
ZVL | 20 | 52 | 22,2 |
SKF | 25 | 62 | 25,4 |
SKF | 30 | 72 | 30,2 |
SKF | 35 | 80 | 34,9 |
The letter E in the first two rows is part of ZVL's catalogue designation and has not been omitted. These designs are 19 mm wide. If the part has a different marking, check its own sheet instead of assigning a dimension from a similar designation.
3205 or 3305? An example of checking the installation space
Suppose a bearing with a 25 mm bore has been identified. In the table, ZVL 3205 has dimensions of 25 × 52 × 20,6 mm, while SKF 3305 ATN9 measures 25 × 62 × 25,4 mm. The bore is the same, but the outside diameter and width differ. This shows why selecting only “a bearing for a 25 mm shaft” is not enough.
Even after finding matching dimensions, the design and operating requirements must still be verified. A dimensional table cannot determine the permissible load, speed or a substitute for the complete assembly.
What should you add to a bearing enquiry?
- The full designation and manufacturer of the existing part.
- Dimensions d × D × B, stating whether they come from a catalogue or measurement of a worn part.
- Closure type: open, shielded or sealed.
- Required clearance, cage, accuracy class and other suffixes if specified in the documentation.
- Machine model and available data on loads, speeds, temperature and lubrication.
Browse double-row angular contact bearings in NERON's range. If the designation is illegible or you are comparing different brands, send the details via NERON's bearing-selection contact page. Providing the full designation and three dimensions narrows the selection without guessing the design.



